The CNC Side Hustle (Expired) › Forums › CNC Tech Forum › Troop Tray “Stars” VBit Engraving in CNC KickStart

Tagged: ,

  • Troop Tray “Stars” VBit Engraving in CNC KickStart

    Posted by Bo on November 19, 2026 at 4:13 am

    1. I don’t have a bowl and tray bit so I used an IDC 1/4″ endmill to carve the pocket. I cut the tray to .625″ and, after adjusting the stepover from the bowl and tray bit, the final cut was good.

    2. Next, I moved to the Stars and started out (incorrectly) setting the top of the material (Z) at the tray botton (.625). The VBit plunged into the bottom, made a nice hole in the tray and into the spoil board. After re-setting Z to the original top of the material, I was still unable to carve the stars. I am using a 90degree VBit Chamfer with a 1/4″ diameter. I tried changing start depth, tool pass depth and cutting depth but the point of the 90 degree VBit barely touches the bottom of the tray while making an airpass (I thought) of the two part star cut and then moves on to the next star position. After pulling the tray off the CNC spoil board, I discovered what I thought was a dimple made by the tip is actually a perfectly formed star so tiny it’s barely visible. Star toolpath is confirmed to be VCarve/Engraving with the 90degree, 1/4inch VBit Chamfer.

    3. When I moved on to the next toolpath for the Stripes and Star Field (2D Profile), I continued to use the 90degree 1/4inch VBit Chamfer. Start depth is .625 with a cutting depth of .12inch. These cuts were good. The depth of the flag stripes may be a bit deep but they’re sharp and clean.

    I’m looking for suggestions to change the toolpath settings or the VCarve toolpath for the stars.

    Thank you.

    Bo Brown

    Miranda replied 1 day, 19 hours ago 2 Members · 3 Replies
  • 3 Replies
  • Miranda

    Administrator
    November 19, 2026 at 3:31 pm

    Hey there!

    Thanks for the detailed explanation! It sounds like you’ve got the pocketing and stripes figured out. Let’s see if we can get those stars looking right.

    The first thing that stands out is your V-bit. The Troop Tray project was designed using a 60° V-bit, but you’re using a 90° V-bit with a 1/4″ diameter. That difference can affect the depth and appearance of the stars.

    Here’s what I’d recommend:

    1. Try a 60° V-bit. That’s what I used for the original project. A 90° bit creates a wider, shallower cut than a 60° bit for the same design, so switching should help produce more defined stars.

    2. Check your start depth. Since your pocket is .625″ deep, the engraving toolpath needs to account for that. If you’re using Carbide Create, make sure the engraving starts at the bottom of the pocket rather than the original material surface. Keep your machine’s Z-zero referenced to the original top of the material.

    3. Double-check the tool dimensions. Make sure the software has the correct angle and diameter for the actual V-bit you’re using. A 1/4″ chamfer bit may not have enough cutting diameter for the larger portions of the stars.

    4. Preview before cutting again. Recalculate the star toolpath and check the simulation. You should be able to see whether the stars are being carved at the correct depth and size before running the machine.

    One other thing worth mentioning: changing the pass depth won’t necessarily make the stars larger. With V-carving, the geometry of the design and the angle of the bit determine the final cut.

    Also, before running another toolpath, I’d double-check your Z-zero and use an air pass with the bit safely above the material. We definitely don’t want another hole in the spoilboard!

    I’d start with the 60° V-bit and a fresh toolpath calculation before changing anything else.

  • Bo

    Member
    November 19, 2026 at 3:57 pm

    Miranda, Thanks for your quick response. That’s only going to encourage more questions from me. FYI: I just copied this tool data from M4-American Flag Tray v11 that I downloaded from the KickStart program – 425-VG90 *Astra Coated* Bits&Bits 90 Degree 2 Flute V-Groove Engraving Bit. One of the things I am struggling to learn is the relationship between tool choices and toolpaths so I appreciated your discussion of the VBit’s characteristics. I am using Vectric Makerspace VCarve Pro on a New Wave Shark 544. I’ll change to a 60degree VBit, re-set the Z position and see what happens. Bo Brown

  • Miranda

    Administrator
    November 20, 2026 at 5:13 pm

    Happy to help! And feel free to come back and ask any questions you have, we will do our best to help any way we can!

Log in to reply.